The MasterGage/Professional is packed with exciting patented features that are built to last! The body of the Professional is fabricated from rugged aircraft quality extruded aluminum. All sides are ground flat, square and parallel to each other to within 0.001 inches [as a reference, the human hair is 0.001 inch]. Once ground, the body is then machined to exacting tolerances [0.0002 inches] on computer controlled NC machinery, the surface is then plated with a protective black anodized finish that also presents a superb black non-glare surface for easy reading.

The unit is then precisely and permanently laser etched with scales that are in inches, millimeters and degrees. This allows the Professional to be used on any equipment worldwide - regardless of the measurement standards used.

The Professional has a new patented feature called Instant Recall™ that allows you to recapture any height or angle very precisely. By aligning the location hole in the Memory Link™ to the precision hole of either the Protractor or level Arm you can recall the angle or height with remarkable accuracy and speed. There is capacity for three Memory Links on both the Protractor and the level Arm height gage.

The Professional body has extruded "T" slots in both the top and bottom surfaces, allowing the owner to use special magnets. These magnet accessories are very powerful rare earth [neodymium boron] magnets that fit into the "T" slots. A valuable Accessory that insures rock solid rigidity while making critical measurements.

The Protractor is high quality aluminum, red anodized plating with a hairline cursor for easy reading of the laser-etched angles. The actual red hairline is only 0.003 from the laser angular markings, thus eliminating any parallax difficulties. The angular markings are in ½ degree increments. A ¼ degree can easily be read - now that's accuracy! The Protractor has a stainless steel working edge called a "knife edge". This 1/16 thick piece of stainless steel fits easily between the carbon tips on the saw blade, allowing easy angular reading against the body of the saw blade. The Protractor can measure both acute angles [less than 90 degrees] and obtuse angles [greater than 90 degrees].

The level Arm is made of ½" x ¾" x 3 3/8" aircraft quality aluminum, hard anodized for durability [hardness equal to sapphire]. The arm is spring loaded so that it automatically levels itself for precise measuring - it never goes out of alignment! The Level Arm glides through sawdust with ease and never clogs up.

The Level Arm is also designed to accommodate a Depth Gauge Rod. The Depth Gauge Rod allows you to measure things like blind holes, mortises and dado cut depths easily and accurately.

The included precision Dial Indicator will give you machine shop accuracy [1/1000 inches] capabilities for all your machine alignment, calibration and setups.

The MasterGage/Professional Manual is very comprehensive and richly illustrated with over 75 pictures.

As a new proud owner, you will have your Professional personalized with your name on a solid brass nameplate - free of charge.

The MasterGage/Professional also features a permanently embedded red medallion metal disk "Birthplate", laser etched with the year it was built.

The Professional can accept many specially designed Accessories. You can customize your Professional to your individual needs.

The MasterGage/Professional comes with a 30 Day Money Back Guarantee PLUS a Lifetime Guarantee Policy on materials and workmanship, including the Dial Indicator.

All parts are precision made and interchangeable, a part made last year will fit a Professional made today, next year and years to come! If a part is lost or damaged, it can be quickly replaced by our factory.

•The precision on-board Dial Indicator is accurate to within  thousandths of an inch! As a point of reference, a human hair is one  thousandths of an inch [.001 or 1/1000]. A piece of bond paper is  approximately four thousandths of an inch [.004 or 4/1000].
•Comes with two dial indicator stems, one a 1.0 inch long and the  second a 2.0 inch long extension. They accommodate any distance  from the miter slot to the saw blade for all tablesaw manufacturers.
•The SuperBar fits all 3/8 x 3/4 miter slots, including Sears brand  [ShopSmith version also available].
•Has a unique, patent pending adjustment system to insure glass  smooth motion in the miter slot.

The SuperBar Package Contains the Following:
• SuperBar - with its unique patented adjustment system. All hardware made of high quality stainless steel • Precision dial indicator, 1.0 inch travel, with accuracy to .001 inches(1/1000) • 1.0 inch long stainless steel extension stem • 2.0 inch long stainless steel extension stem • Hex wrench for mounting Dial Indicator • Hex wrench for adjustment system • Detailed operating instructions

•Angles marked from left to right. 0° to 180° - to 1/2° accuracy.
•Angles marked from right to left. 0° to 180° - to 1/2° accuracy.
•Both left and right hand, 90° to 0° bevel/miter angle scales.
•Inch height gauge, 3.0 inches, graduated to 1/32".
•Metric height gauge to 8 centimeters, graduated to 1 millimeter.
•Precision scales are laser etched and generated by computer.
•Brushed anti-glare, black anodized surface for easy reading.
•Unit is made from 3/32" x 4-1/2" x 8-1/2" aircraft quality aluminum.
•Convenient nail mounting hole for storage

•OUTSIDE measurement ranges from 1/16 to 2 1/2 inches.
•INSIDE measurement ranges from 1/4 to 1 1/2 inches.
•All stair step measurements are in 1/16th inch increments with accuracy to +/- 0.005 inches [five thousandths of an inch]
•The stair step concept allows the caliper tips to rest against a flat surface, giving an positive, accurate reference surface
•Constructed of thick walled aircraft quality aluminum overall size: 3-3/4" wide x 8-3/4" high x .30" total thickness.
•Red and black anodized plating for contrast and protection
•Precise, permanently laser etched lines into the black surface
•Brushed, anti-glare black anodized surface for easy reading.
•Two convenient holes for wall mounting
•The Caliper Step Gauge can also be free standing, by simply making a wood base with a dado slot to hold the unit

•OUTSIDE measurement ranges from 2 1/2 to 5 1/2 inches.
•INSIDE measurement ranges from 1 1/2 to 4 1/2 inches.
•All stair step measurements are in 1/16th inch increments with accuracy to +/- 0.005 inches [five thousandths of an inch].
•The stair step concept allows the caliper tips to rest against a flat surface, giving an positive, accurate reference surface.
•Constructed of thick walled aircraft quality aluminum overall size: 3-3/4" wide x 8-3/4" high x .30" total thickness.
•Red and black anodized plating for contrast and protection.
•Precise, permanently laser etched lines into the black surface.
•Brushed, anti-glare black anodized surface for easy reading.
•Two convenient holes for wall mounting.
•The Caliper Step Gauge can also be free standing, by simply making a wood base with a dado slot to hold the unit

•The dial indicator is an AGD-1 type indicator with a 1-5/8" diameter face.
•It has easy to read black numbers and markings against white background.
•The dial readings range from 0.000" to 0.100" [0.000 to 10/1000"], per revolution.
•The small dial indicates how many times the dial hand has rotated up to 0.250" distance.
•The bezel rotates to allow you to line up zero with the indicator arm.
•Once the bezel has been rotated to position, there is a locking knob to keep the bezel from moving.
•The back of the dial indicator is flat to insure clearance to any planer structural parts.
•The Planer Jig housing is solid, aircraft quality aluminum.
•The housing is protected with a black anodized plating.
•The dial indicator tip is heat treated, hardened stainless steel.
•The tip is a flat 0.300" diameter surface, ground and lapped to a mirror finish for precise measuring requirements.
•The Planer Blade Setting Jig is held in place on the steel planer cutter head by two powerful rare earth magnet (neodymium - iron - boron).

This section is under construction.